Reset Steps for Ezviz C6N WiFi Camera

Resetting the Ezviz C6N returns its configuration to default settings so the camera can be configured again. This is different from simply restarting the camera, which normally leaves the existing settings unchanged.

[reference] Title: Reset Button Text: On the C6N pan-and-tilt camera, the Reset button is located in the area beneath the lens near the Micro SD card slot. Title: Reset Hold Text: Press and hold the Reset button for about 5 seconds. Title: Ready Indicator Text: After the reset and startup process, a fast-flashing blue indicator means the camera is ready for Wi-Fi configuration. [/reference] [warning] Resetting returns the camera configuration to default settings. Be prepared to configure the camera and its Wi-Fi connection again afterward. [/warning]

Restart vs. Reset

[compare] Restart | Turns the camera off and back on without intentionally returning its configuration to default settings. Reset | Returns the camera configuration to default settings and requires the setup process to be completed again. [/compare]

A restart is the lighter action when you only want to power-cycle the camera. A reset is more appropriate when the current configuration needs to be cleared, such as when preparing the camera for a new Wi-Fi configuration.

Before Resetting

[checklist] * Keep the Ezviz C6N powered on * Be prepared to configure the camera again after the reset * Tilt the camera lens upward so the Micro SD card and Reset area can be accessed * Locate the small Reset button before pressing anything [/checklist]

Find the Reset Button

The Ezviz C6N is an indoor pan-and-tilt camera. Gently tilt the lens upward to expose the compartment beneath the lens. The Reset button is located in this area near the Micro SD card slot.

Reset ezviz camera
[tip] Use gentle pressure when moving the lens upward and when pressing the small Reset button. [/tip]

Reset the Ezviz C6N

[step] 1. Leave the camera connected to power and switched on. 2. Tilt the lens upward to access the Micro SD card and Reset area. 3. Locate the small Reset button. 4. Press and hold the Reset button for about 5 seconds. 5. Release the button and allow the camera to complete its reset and startup process. 6. Wait for the indicator to fast-flash blue before beginning Wi-Fi configuration again. [/step] [note] Some cameras may provide an audible confirmation during the reset process. If there is no prompt, allow the camera time to restart and watch the indicator instead. The reset and startup process can take around one to two minutes. [/note]

After the Reset

Once the reset is complete, the previous configuration has been returned to its default state. The camera then needs to be configured again before normal connected use.

  • Wait until the camera finishes starting up.
  • Check for the fast-flashing blue indicator that signals readiness for Wi-Fi configuration.
  • Run the camera setup process again to connect it to the intended Wi-Fi network.
  • Allow configuration to finish before checking normal camera operation.
If the camera has only just been reset, avoid repeatedly pressing the Reset button while it is still starting up. Give the device time to complete the process first.

When a Reset Is Useful

A reset can be considered when you intentionally need to clear the current camera configuration rather than simply restart it.

  • Preparing the camera to use a different Wi-Fi network.
  • Starting the Wi-Fi configuration process again.
  • Returning the current camera settings to their default state.

For a temporary interruption or simple power cycle, restarting is the less disruptive option because it does not intentionally return the settings to their defaults.

[dosdonts] Do: Keep the camera powered while performing the reset Do: Wait for the camera to finish restarting before configuring it again Do: Look for the fast-flashing blue indicator before Wi-Fi configuration Dont: Use a reset when a simple restart is all that is needed Dont: Repeatedly press Reset while the camera is still completing the reset process [/dosdonts] [faq] Q: How long should I hold the Ezviz C6N Reset button? A: Hold the Reset button for about 5 seconds, then release it and allow the camera to restart. Q: Where is the Reset button? A: Tilt the lens upward. The Reset button is located beneath the lens near the Micro SD card slot. Q: How do I know the camera is ready for setup again? A: A fast-flashing blue indicator means the camera is ready for Wi-Fi configuration. Q: Does resetting keep the existing configuration? A: No. A reset returns the camera configuration to its default state, so setup needs to be completed again. Q: Is restarting the same as resetting? A: No. Restarting power-cycles the camera while normally keeping its settings. Resetting returns the configuration to its defaults. Q: What if I do not hear a reset confirmation? A: Allow the camera to complete its reset and startup process and watch the indicator. The process may take around one to two minutes. [/faq]

Note :

"Reset Steps for Ezviz C6N WiFi Camera"

This content is uploaded by APP SETUP DEVELOPER and available on Google Play Store. APP SETUP DEVELOPER do not own this content and this content credits to their respective owners listed in the source link. Hopefully useful and share this app.

Design and Coded by www.idblanter.com www.blantertheme.com www.blantermedia.com (Rio Ilham Hadi) 08888905441