Blue Iris Setup for Ezviz C6N WiFi Camera

Use this guide to add an Ezviz C6N to Blue Iris through its local network stream. The original configuration was tested with camera model EZVIZ CS-CV206-C0-3B2WFR, Blue Iris 5.3.9.17, and EZVIZ PC Studio 2.1.1. Menu names and behavior may vary with other camera or software versions.

[reference] Title: Camera IP Address Text: Blue Iris needs the local network address assigned to the camera. Title: Verification Code Text: Keep the camera verification code available. It is printed on the camera label and may also be available from the camera settings. Title: Main Stream Text: The original tested configuration used /Streaming/Channels/101. Title: Sub Stream Text: The original tested configuration used /Streaming/Channels/102. Title: Audio Text: The original Blue Iris configuration used RTSP alternate AAC decoder with the audio path left blank. [/reference]

Before Setup

[checklist] * The Ezviz C6N has already been connected to the network * The camera IP address is available * The camera verification code is available * The computer running Blue Iris can reach the camera on the local network * If following the original tested configuration, Image Encryption is turned off for the camera [/checklist] [note] The Image Encryption setting reflects the original tested setup. Camera behavior may vary by model, firmware, and software version. [/note]

Configure Blue Iris

[step] 1. Open the camera settings in Blue Iris. 2. On the Video tab, select Configure next to Network IP. 3. Enter the local IP address of the Ezviz C6N. 4. Set the Main Stream path to /Streaming/Channels/101. 5. Set the Sub Stream path to /Streaming/Channels/102. 6. Set Audio to RTSP alternate AAC decoder and leave the audio path blank. 7. Open the Audio tab, enable the audio channel, and select IP Camera Stream. [/step] [tip] Treat the stream paths and menu selections as tested values rather than universal settings if your C6N model, firmware, or Blue Iris version differs from the original setup. [/tip]

Access Advanced Camera Settings

The original workflow used EZVIZ Studio to expose additional local camera settings. The camera and the computer running EZVIZ Studio need to be on the same network or VLAN for local device discovery.

[step] 1. Confirm that the camera is already connected to the network. 2. Install and open EZVIZ Studio on a computer that can reach the camera on the local network. 3. Open the EZVIZ Studio config folder. The original installation used C:\Program Files (x86)\Ezviz Studio\config. 4. Copy AppConfig.ini to the Desktop for editing, or edit it with sufficient system permissions. 5. Add a LocalOperation section and set Show=1. 6. Save AppConfig.ini and copy it back to the config folder, replacing the previous copy. 7. Open or reopen EZVIZ Studio. 8. Sign in to the EZVIZ account, or use the camera verification code for local device access when that option is available in the installed Studio version. 9. Open All Devices and confirm that the camera appears among devices detected on the LAN. 10. Select Advanced for the camera to review its additional settings. 11. If Advanced is not shown, the original workflow used Devices on LAN and the camera verification code as an alternate local-access path. [/step]
AppConfig.ini entry: [LocalOperation] with Show=1 beneath it.

Settings to Review

  • System -> General -> Time: The original setup used an internal NTP server so the camera could maintain time without relying on an internet NTP service.
  • Network -> EZVIZ Cloud: The original local-only configuration disabled EZVIZ cloud connectivity.
  • Image -> Video Display -> Show Yingshi: The original setup disabled this option to remove the EZVIZ logo from the video stream.
  • Image -> Video & Audio: Review the maximum bitrate, bitrate, video quality, and the available Main and Sub Stream settings as needed.
[warning] Change optional network, cloud, or video settings only when they are needed for your setup. Verify the Blue Iris stream after each significant change. [/warning]

Local-Only Use

In the original setup, Blue Iris became the primary local viewing system after configuration, so the EZVIZ mobile app was no longer required for day-to-day viewing. The cameras were also used without general internet access while remaining available on the local network.

Local-only operation can vary by camera model, firmware, and enabled features. Keep the camera and Blue Iris reachable on the same local network when using this arrangement.

After Setup

If EZVIZ Studio is no longer needed after configuration, remove it through the normal application-management process. The original environment reported that an npf service remained after uninstalling EZVIZ Studio.

[warning] A remaining service should not be treated as evidence of malicious software. Avoid manually deleting services or program files unless you have verified what they belong to and understand the effect of removing them. [/warning] [faq] Q: Will these exact Blue Iris settings work with every Ezviz C6N? A: Not necessarily. The configuration was tested with EZVIZ CS-CV206-C0-3B2WFR, and stream paths or available settings may vary with other C6N variants and software versions. Q: Is EZVIZ Studio needed for normal Blue Iris viewing after setup? A: In the original workflow, EZVIZ Studio was mainly used to access advanced camera settings. Blue Iris handled the ongoing local camera stream afterward. [/faq]

Note :

"Blue Iris Setup for Ezviz C6N WiFi Camera"

This content is uploaded by APP SETUP DEVELOPER and available on Google Play Store. APP SETUP DEVELOPER do not own this content and this content credits to their respective owners listed in the source link. Hopefully useful and share this app.

Design and Coded by www.idblanter.com www.blantertheme.com www.blantermedia.com (Rio Ilham Hadi) 08888905441